This is the Futaba 3PK Super Pistol Grip 3 Channel Transmitter
This Version Does Not Include Module, Servos or Receiver.

FEATURES: Upgrades over the original 3PK include;
Expanded Driver Menu, with "New Driver" "Race-Ready" and "Expert"
menus and a mid-level "Big" menu for drivers of 1/5 scale and
larger vehicles
Redesigned Keypad, with jog button giving access to four different
directions by moving button left, right, up or down and then
pushing in
Vibrating Alert System, functions like a timer to let driver know
when to bring a nitro car in for a pit stop or check battery life
of electric model
Increased Model Memory, 20 models also compatible with CAMPac module
that adds another 10 models
Throttle Mode Select, choice of two servo neutral points 70/30 for
nitro models and 50/50 model for electrics

Features unchanged from the original 3PK include;
APA (Advanced Positioning Adapter) for customizing balance and
wheel position
Large Backlit LCD Screen with adjustable contrast and 128 x 64
resolution
"Direct Select" single button access to 8 preassigned functions
Adjuster feature restores compromised settings to factory default
Assignable switch and dial functions
10 Digit Model and user naming: English or Japanese characters
PCM/PPM/HRS Selectable with 3-ch adjustable FailSafe for PCM/HRS
3 Function selection modes (New User, Race Ready Driver and Expert
provide 1/2/3 menus of features for just the right fit!)
PLUS the direct selection 2-key menu to up to 6 functions.
Steering Dual Rate and Dual Rate 2, both adjustable while driving
Servo display to show all 3 servo positions for easy setup/diagnostic
Anti-Skid Brake System (ABS) (Keeps tires from skidding, or
locking-up, even on gas cars) (with 5 adjustments)
Throttle Acceleration (decreases lag time before clutch or brakes
are engaged)
Steering and throttle exponential (3 forward expo types)
end point adjustments for all 3 channels (EPA/ATV)
Steering and Throttle servo speed limiters
Brake mixing for 1/5th scale cars with separate front and rear brakes
System adjustments for back lighting, pilot lamp color, home display
Servo Reversing
Idle-up for easy starts and engine cut for boat engine shut off
Start (Preset throttle start control. Limits throttle at the
beginning of a race to give smoother acceleration and less wheel
slip.) (similar to traction control on 3PJS)
Advanced timer w/100 lap recall & trigger activation
Trim/dial function selection (can assign different functions to the
different trim controls and dials)
Subtrim adjustments
Step trim adjustments (allows changing of trims in finer increments)
Programmable mixing
Tilt mixing for adjusting the trim tabs with the 3rd channel on boats
Third channel assignable to any dial/switch/trimmer/mix
MC-SETUP function for HRS receivers to properly setup ESCs
ADJUSTER function to manually calibrate trigger and wheel

EQUIPMENT FEATURES:
Optional DSC cord support for operating receivers without transmitting
LARGE REAR Facing LCD plus Seven Color Pilot Lamp for easy ID.
One Year Warranty
Digital trim with reset
Left Hand reversible
Steering wheel tension adjust (can be adjusted without opening radio)
Trigger stop function (mechanical ATL) and programmable ATL
Display switch (allows functions to be set without transmitting)
Audible, adjustable alarm tone and lap counting tones
Headphone jack for hearing the alarm tones at a noisy track

INCLUDES: 3PK Super Transmitter with antenna
Transmitter NiCd NT8F700B, FUTM1462
Switch Harness, FUTM4350
Offset wheel adapter and screws
Instruction manual and warranty card
Hex wrench
Charger FBC-19B(4), FUTM1830

OPTIONAL: * Campac 16K, 10 Model Memory, FUTM9405
* DSC cord-To use the DSC function use-DSC Cord, FUTM4245
* MC SETUP cord
* Dry cell transmitter battery case, FUTM1563

REQUIRES: Transmitter Module: FUTL13**
Digital servos (if using in HRS mode)
Receiver: Futaba R203HF, FUTL0344
Receiver Crystal: FUTL52**, must match channel of crystal in module
Receiver NiCd battery

SPECS: Operating System: FM/PPM, HRS_FM or PCM1024 switchable
Transmitting Frequency: 27MHz
Power Supply: 9.6V NiCd
Current Drain: 250mA or less

COMMENTS: This radio is sold without servos and REQUIRES DIGITAL SERVOS ONLY
and 6V when using an HRS receiver. Non-digital servos are fine on
PPM/PCM.